Custom 3D printed cabinet knob

Preset: 38 mm dome cabinet knob for #8-32 screws

Knob shape

Knob size

Width across the front of the knob. Most cabinet knobs are 25–38 mm (1–1½ in).
How far the knob stands out from the door, from the back face to the front.

Screw

The machine screw that comes through the door. Most knobs in North America take #8-32 and most elsewhere M4. The screw is not included.
The screw cuts its own thread in the printed hole. If it is too hard to turn, choose Looser; if the knob is loose, choose Tighter. Each step changes the hole by 0.15 mm.
How deep the screw hole goes into the knob. A screw longer than the door thickness plus this depth will not tighten.

A 3.5 mm hole for an #8-32 screw, which cuts its own thread. Screw length: door thickness plus 6 mm to 10 mm. For a ¾ in door, a 1 in #8-32 screw. The screw is not included.

38 mm dome cabinet knob for #8-32 screws

38 mm face30 mm projection10 mm hole3.5 mm screw hole, centred · door face at the bottom

About this round cabinet knob

A round cabinet or drawer knob in the size and shape you choose, made for the machine screw already in your door. Choose the shape, enter the diameter and projection, pick the screw, and download an STL to print. There is no CAD to learn.

What people make with it

  • Match an old set — measure an existing knob across its face and from the door to its front, and enter both.
  • A whole kitchen — make one design and print as many as you need, so every door matches.

This Template makes round knobs on one screw. Square knobs, bar knobs and two-screw pulls are separate designs.

What you can change

  • Shape. Mushroom, with a narrow neck under a wider cap; Cylinder, with straight sides; or Dome, rounded on a short neck.
  • Size. From 20 to 50 mm across the face and 18 to 45 mm from the door, in millimetres or inches.
  • Screw. An #8-32 or M4 screw, how deep its hole goes, and a tighter or looser hole if your first print needs it.

Printing it

  • It prints as it stands on the door, back face down, with no supports: no surface leans out more than 45°. The screw hole runs straight up into the knob from the back.
  • The screw cuts its own thread in the printed hole. Print one knob first and try it on your screw: if it is too hard to turn, choose a looser hole; if the knob is loose, a tighter one. Then print the rest.
  • PETG, or PLA with at least four walls, is a good start. Brittle or filled filaments may split when the screw goes in.
  • You download an STL or 3MF file, ready for your slicer. The screw is not included.

Cost and licence

  • Free. Generate and download it without an account.
  • Creative Commons Attribution 4.0. You may print it, change it, share it and sell your prints, as long as you credit IteraMesh as its creator. Read the licence

Common questions

Which screw do I need?

Reuse the screw in your door if it fits. Most knobs in North America take #8-32 and most elsewhere M4. Its length should be the door thickness plus at least 6 mm, and no more than the door thickness plus the screw-hole depth, or the knob will stop before it tightens.

How strong is it?

No strength is claimed. A printed thread is weaker than a metal one, and it depends on your material, walls and settings. Use it for light cabinet and drawer use, and check your own print.

Can I use it on a room door?

No. Room-door knobs turn a latch and take much more force. This knob is for cabinet doors and drawers only.